Tuck the paper under the triangle of the corner. Just a pinch. Fold under the triangle. Reverse, again. PULL To the cross. Open one layer and squash. Separate flap, just to prepare next step temporary.
Reverse to the back. Pull tip out. Fold tip following upper layers and flatten it. Lower angle is NOT bisector. Edges do not match Fold a small portion. Fold just upper layer. Fold the two layers. Squash nose. Mini-crimp at sides. A bit oblique.
Repeat but reverse one layer. Squash it. Edges to axis. Mountain reference comes while folding. These "zooms in" are face and tail from different sides. Reverse all these creases like a sink.
Work on this area at the next step. Turn to the side opposite to the face. Open and lift a tip. A swivel is required. Squash to flatten. Turn the paper. Just one layer. Gap Fold like a water-bomb base, but upper valley diagonals have a different angle see "Gap". Fold the "V" of the neck after the water-bomb base. The valley fold of the neck has many options. The arm goes under the head layer. Just inner layer. View from below. Reverse one tip, like a sink. Notice that inner graft is a long pocket.
Trap the reversed tip inside the graft. Back is locked. La solapa interior debe posicionarse hacia abajo 65 B Al estirar, la solapa interior debe posicionarse hacia abajo 64 A 63 62 Bajar y aplastar las solapas laterales Tirar de la punta destrabando las capas.
Crease in half. Crease the angle bisectors. Crease through the circles. Crease at the circles. Divide the indicated regions into fourths with alternating mountain and valley folds. Zoom in at the circle. Make the indicated creases. Squash-fold the flap. Spread squash-fold the two flaps. Turn over and rotate. Collapse on the creases. Unsink one layer from the pocket. Fold toward the center. Crease halfway between the existing creases. Close-up of the previous step.
Fold the two points over. Open-sink the four flaps. Fold down. Zoom out. Open-sink the right flap in and out in thirds. Mountain-fold in half. Open-sink fold along the existing creases. Rabbit-ear fold the corner.
Fold one layer up in front and one layer down in back.. Fold the front layer in half, making a squash-fold on the upper right and an outside reverse-fold on the lower right. The fold must be performed behind simultaneously. Fold two layers down and squash-fold the top middle flap. Unsink the region under the squash-fold in the previous step. Release the trapped paper under the pleats and spread open the layers. Open-sink on the crease. Push in the tops between the pleats and refold them.
Repeat steps on the next flap. Fold one layer to the left. Fold the flap back to the right. Fold and unfold along the angle bisector. Repeat steps on the left. Repeat steps behind. Petal-fold the front face and swing the resulting flap to the left. Reverse-fold the left flap in and out on the creases. Crease breakdown is on the right.
In progress. Fold one layer to the right and spread-squash the hidden flap. The region below the fold will not lie flat. Open-sink the left flap and the little pleat together along the angle bisector. Fold one layer to the right. Fold the layer to the right in front and behind and simultaneously outsidereverse-fold the lowerleft flap.
Unsink the small hidden flap. Fold the flap to the left and flatten the model. Open-sink halfway. Fold the flap to the left to close up the pocket.
The lower region will not lie flat. Wrap the small flap from underneath around to the front side. Incorporate the reverse-fold for the little flap and fold the side flap to the left. Release the trapped layers. Crimp-fold the top flap. Repeat steps here. See crease breakdown of the hidden flap. Fold the big flap and the two thin flaps behind it to the right and spreadsquash the lower flap. Fold the layer to the left in front and behind, and outside reverse-fold the flap at the bottom.
Swivel-fold the flap on the front and behind and outside reverse-fold the bottom flap. Fold and unfold along the Fold and unfold along the angle bisector through all layers. Inside reverse-fold in and out on the creases through each layer separately. Pinch the flap on the creases and swing it to the left, closing up the pocket. Reverse-fold the flap in and out on and swing the left flap upward. Repeat behind simultaneously. Fold one layer to the right and bring the lower front flap down.
Grab five layers at the circle and fold them to the right, spreading open the layers in the lower left flap and swiveling it up to the center.
In the process, you will undo step Squash-fold the big flap. Fold the point up. Unsink the hidden point directly behind the flap. Closeup shows crease breakdown at the tip. Petal-fold the flap, then swing the tip to the left. The next few steps will focus on the circled region. Fold the point down. Valley-fold the flap to the center and unfold.
Valley-fold the flap along the angle bisector and unfold. Reverse-fold the flap in and out on the creases. Reverse-fold the flap in along the angle bisector. Fold one layer left. Repeat steps on the right side. At the circle, grab three layers and fold them to the left. Repeat steps on the second flap on the left. Rabbit-ear fold. Squash-fold the upper half of the right flap. Pinch the flap and raise it up on the creases. Repeat steps on the little right flaps. Fold the two thin flaps to the left.
Fold one flap upward. Repeat steps Then turn over. Unsink from the right pocket. Look for the hidden edge on the right two layers deep and crease the other layers parallel to that edge. Reverse-fold in and out through each layer individually, just like step Unsink the layers in the darkened region, just like step Fold the little flap up. Push in the sides, pinch the flap, and swing it to the right, closing up the opening simultaneously, like step Fold one layer to the left and spread-squash fold the top.
Simultaneously fold the lower flap down. The paper will not lie flat. Unsink the small flap at the top. Grab one layer at the circle and fold it to the left while making a spread-squash fold at the top. Fold one layer to the left and spread-squash fold the bottom. Grab one layer at the circle and fold it to the right. Grab one layer at the circle and fold it over to the left. Grab two layers at the circle and fold them to the right. Grab four layers at the Unsink the inner circle and fold them to the pocket.
Simultaneously pleat the front and back layers of the front central flap and swing the flap upward. Grab four layers at the circle and fold them to the left.
Fold one flap to the left. Fold the top flap down and incorporate the reverse-fold. Fold the flap to the right. Spread-squash fold the flap. Swing the flap back up. Squash-fold the flap upward. Unsink the inner layer in the pocket created from the previous squash-fold. Fold the layer to the left and incorporate the reverse-fold. Fold the two layers back to the left.
Swing the flap to the left. Repeat steps on the right. Mountain-fold the two bottom points behind and swing the top center points down simultaneously. Fold the top middle flap down. Fold the flap up. Grab three layers at the little circle and fold them to the right in front while incorporating the two reversefolds in the bigger circles.
Fold one flap on the left over to the right. Grab two layers from the circled region and fold them to the right. Grab three flaps at the circle and fold down. Fold two points to the right, squashfolding the indicated hidden edges.
Fold all upper layers downward. Be careful to avoid ripping. Swing two points on the right to the left. A tree displaying the current arrangement of flaps is shown above. Grab two layers at the circle and pull them upward.
Grab two layers at the circle and fold them upward. Fold one flap to the right. Fold all layers down while incorporating the reverse-fold.
Reverse-fold the side of the flap. Repeat on the back side of the flap. Crimp-fold the flap so that it lies along the dotted lines. Open up the layers. Reverse-fold the two flaps. Reverse-fold the tip. Closed-sink five of the seven the layers on the back side of the hand individually. Close up the layers. Reverse-fold the rear flap. Reverse-fold the last two layers behind.
Outside reversefold the three claws. Completed forearm. Hirschberg Alien Raptor 16 Double rabbit-ear fold the left flap, including the small internal flap outlined by the dotted lines. Spread the layers evenly. The following steps will focus on the circled region. Crimp-fold the tip.
Fold the two long points to the left. Reverse-fold each of the three small flaps. Pleat the flap so that it points straight down. Double rabbit-ear fold the flap to the right. Inside reverse-fold the flap downward. Outside reverse-fold the flap to the left. The next few steps will focus on the smaller circle. Fold the layer down. Repeat steps on the other two points. Reverse-fold one hidden layer from behind the leg. Fold the small flap to the left. Rabbit-ear fold the small point upward.
Grab two layers at the circle and lift them upward. Note that the body and tip of the tail are not shown. Valley-fold the side flaps to the center along the angle bisectors.
Tuck the top layer into the pocket in front of it. Valley-fold the raw edge down. Fold the next layer in along the angle bisector and tuck it under the flap in front of it. Mountain-fold the small flap behind.
Close up the model. Spread open the side layers and raise the lower tip. Close-up of wing Repeat on the other side. Reverse-fold in and out twice. Squash-fold the left flap. Fold the flaps down. Petal-fold the flap straight up. Mountain-fold inside.
Swing the wing to the left to view the other side. Pull the small side flaps out to reveal the white spot. Note that only the flap is shown. Pleat the flap and fold the left side to the right. Swing the wing back to the right. Swing the little flap to the right. Squash-fold the next flap. Repeat steps on this wing. Move the point upward and squash-fold the lower edge.
Fold the point out to Fold the raw edge to the left while the right and squashrepeating steps here. Pleat as shown. The valley-folds were folded in the previous step. Spread open the right flap. The next few steps will focus on the top side of the flap. Fold and unfold in fourths. Unfold to step Open-sink in and out on the creases folded in step Valley-fold the flap up as far as it will go.
Part of it is hidden under the flap on the left. Rabbit-ear fold the small flap and swing the point to the left. Swivel-fold the pockets as shown. Repeat step on the other three small flaps on the right. Repeat steps on the lower half. Outside reverse-fold the tip of the shorter flap.
Mountain-fold both layers together on the top and bottom into the pockets behind them. Outside reverse-fold the tip of the longer flap. Crimp-fold the flap. Slightly pinch the flaps in the front layer and spread them to round out the region.
Pull out the trapped layers in the tail. If you have any questions, please contact the Convention Committee at convention-info [at] origamiusa. PCOC takes place in odd-numbered years in the fall. Please note: the guidelines document is a work in progress and subject to change. If you would like to start up an OrigamiUSA convention in another part of the country the South is still open, as are even-numbered years , please contact the Convention Committee at convention-info [at] origamiusa.
If you are interested in organizing such a conference, please contact the Convention Committee at convention-info [at] origamiusa. With some manipulation of the tail and Fold to shape bird as shown. Begin with an equilateral Fold to the crease line in the Fold and fold. Imagine BCD as an top layer is folded. Bring the lower edges shown, at the Valley fold as to the middle. Fold down and crease Reverse fold again along Fold and unfold, creasing Fold over Repeat Steps 12 to 15 on the other side.
Outside reverse fold on the left Rabbit's ear. Mountain fold the Steps 22 to 24 are Reverse fold on the close ups of the right Outside reverse at the top while crimp folding below Sitting pretty! Make two consecutive reverse fold to form the beak Use a square of paper. Steps Repeat on the back. Mountain folds only in the first and last layers.
If you want, put the stalk in it, by inserting a piece of thin wire or straw into the down hole. Fold in half. Enlarged; Fold 3 corners 1. Start from square with boat color 2. Right edge meets the 1st left crease up; Make creases 4. Repeat steps for left 8. Open to form 3D hand side 9. Start from rectangle 3x4, A4, 3. Fold 3 corners 2. Enlarged; Fold and unfold letter-size, or most of the magazine papers with boat color up; Fold right side; Fold and unfold left side 6. Repeat steps for left 4.
Open to form 3D 8. Try to make this one. A lies on line Made 2 toned paper. Back Side. Front Side. Unfold and tuck in two triangles pocket. Best m. Or Make your own by mountain and valley folding. All Rights Reserved A 10cm x 14cm sheet produces a model 3cm x 3cm base and 4 cm high 1. White side up. Valley 2. Mountain crease try not 3. Mountain crease at 45 crease at 45 degrees.
Creasing finished. In progress. All triangular f laps inside. Push small 8. Side view. Valley down on triangular flaps against wall, creases from step 3. You may then large flaps. Tips of large need to flatten the box slightly flaps need to be folded a bit.
Braided Paper - J. Fold and unfold laterally. Fold and unfold in fourths. Fold and unfold. Following the existing creases, 5. To complete the base, 6. Sink all four corners. No longer an X-Ray view. X-Ray view, reverse fold 8. Pleat sink the two flaps. Pull point A all the way down the two flaps. Repeat on other Repeat on the other three as far as it will go, thinning the three sides. Repeat on the next flap. Repeat on the last flap, tucking Point A will become covered. The first level is complete.
Fold the next flap down. Completed model. I am using a dollar bill, starting front Make a Water bomb base while folding side up crease it then turn it over. Reverse fold the bottom flap up half way mark of the top or bottom to form front paws, Make a Rabbits of the WB base. Still in enlarged mode, Reverse fold the front to make a nose, the top part of the nose will co-operated if you force it to, much like a small child or an ex- spouse. Do an uneven double rabbits This is shown enlarge to make ear fold along the lines shown to finish it possible to see the fold lines.
Then we shrink the picture Squash down the ears, on both back down. Now we need to work inside the model so the next view is interior of the model. Now do a double inside reverse fold to form the haunches. Swivel fold up the legs 14 on each side. I used the back of the bill to give you helpful reference points. Then open up the model to lock the head in to place. See next diagram 16 This is inside the model and magnified, to lock the head in to place just use a simple valley fold on the tip of the crimped material.
Then you are done! Just for continuity here is the finished model still in the attitude you started with. While I designed it to sit up, it can go on all fours. With any luck at all your rabbits will all look a little It just might tend to have the different, each time you make it! Almost all the nose a little close to the ground.
A 6 this. You can middle. All Rights Reserved A dollar bill makes a model 55mm long with a 65mm wingspan. For your first attempt, begin with a 3x7 rectangle larger than a dollar bill. Begin black side up. Crease halfway, 3. Soft mountain-fold Valley-crease, the horizontal making a mark. Pinch where mark from 5. Use mark from previous 6. Use the 2 existing step 2 hits edge. Pinch halfway marks 8. Mountain in half. Crease and unfold. Crease and unfold, bisecting.
Reverse-fold, in-and-out. Crease from previous step will align with vertical crease. All Rights Reserved Pleat top layer on Reverse-fold, following Pleat top layer, softly existing creases. Unfold to on the dotted line. Bisect angle. Softly on Creases exist as shown. Follow hidden vertical edge. Unfold to step Softly on dotted line. Collapse on the creases. Mountain-fold is the First close up the mountain- reach corner.
Repeat existing half-line. For the valley, fold triangle, pinching the tiny 19 on rear flap. Note shifted creases in fudged area. Close-up of right edge. Fold and unfold bisection , precise, it will be hidden later. Fold and unfold to hidden edge aligning previous crease with Repeat 21 behind. These Fold and pinch, where steps are similar to Push from behind and create a new mountain-crease linking Begin to flatten by pinching the base of the reverse-folds to where shown.
Swing the Undo the reverse-fold standing edge to the right. Then spread the pinch mark of step All Rights Reserved D C align The upper crease Wrap top layer around to To flatten, first align bottom partially exists. Use it to start edges. Careful of tearing of the vertical crease. Reverse-fold hidden Reverse the two creases corner, bisecting. Then Lower crease bisects. Upper just made and add the tiny unfold it.
C Still pushing towards the left, Model is flat again. Swivel Curve the tip towards you also push in at the tiny valley-fold, on existing creases and tuck a bit. Helps keep together. All Rights Reserved E Entire model again. First make the long mountain- folds.
Then make the left valley Repeat on Spread upper layers a bit. Then open model an exact bisection. Then make the right valley not an exact out. Valley-fold, limited by the Closed-sink central ridge folds of step If you have Valley to previous crease and unfold.
Repeat on the halfway. Close up the model again. Reform valley-folds from Tuck into sink, creasing 44, then valley folds from Mountain to shape wing. Close up model, adding new Reverse-fold at overlaps to help Then open model again.
Bottom half is now done. Lift the single-ply Reverse-fold the small Top of model. Then underside of the sink. This distributes the layers of lift wing. Squash the flap lifted in Squash again. Wrap raw edge to the step 50, on existing creases. Tuck long flap into Like so. Repeat sunken pocket. Mountain- Double-rabbit-ear the point on other wing. Repeat fold to shape wing. Reverse- fold at overlap to help secure. Distribute layers evenly.
Curl antenna. Fold wings, Valley 3 Now, fold those flaps side of the model so you get Nolan - Sept. Please read them before folding. The folding sequence seems very mathematical. Fold the bisector. Step 7 indicates the position of the endpoint. Crimp on an existing valleyfold.
The mountainfold starts at the endpoint of that valley and Step 9 indic- ates its angle. Avoid creating the bottom border. Mountain fold starting at A, nearly parallel to Y but widening slightly towards the top. Endpoint C is just a fraction higher than B. Make a tiny mark with your fingernail in the centre of the point. Fold the bisector, starting from the mark in Fold only the bottom third of the point.
Fold the point so that its edge crosses the circled point. Rearrange existing folds on one layer of paper only. Pinch both layers of paper at the indicated spots and move your hands together, curving the paper in between make a bump, not a hollow.
The top point should open out and move down. Pull apart the two layers of the ears. Gently curve the ears, the paper wants to do this anyway. Practice this in a separate sheet first. Inside reverse fold. Get rid of the point by folding it up into the head. Make sure flap A is folded into the tail. Run your thumbnail along the tail furrow and extend it, curving upwards. Gently curve back the paper along the dotted lines. The final model will need a support to stand. Copyright c Herman van Goubergen, all rights reserved.
Distribution for noncommercial purposes is free. Please contact the author if you want to use this model for commercial purposes. Gato J. The left half is only folded double.
Shorter than 8 x 1 is possible, but not as nice. You may first try with a strip of 3 x 1. The diagrams are drawn as if folded of a 3 x 1 strip. Only the finished model is drawn as if folded from a 8 x 1 strip.
BA You may first try with a strip of 3 x 1. Precrease and return to step 2. Form the model, using the creases were made before. Turn back layer. Petal fold with one layer. Note the 9 rectangles 7 8 Fold back layer in half. Keep attention: see on the figures!
Back air-plane fold. Making the eyes. The same too. The leaf with crawling caterpillar completed! Simple chain unit for fast folding. With this we won the Novelty competition at Nottingham Take a rectangle. A4 is ok. Preliminary fold. Inside reverse folds. Valley folds to the centre. Knight and Rook Repeat behind. Repeat Behind. After step 8. Squash each After step Bishop and Queen Pawn and King start here.
Flip each flap 2. Mountain fold inward. Inflate the the model. Bishop: Start after step 12 of page 1. Fold and unfold 2. Fold and unfold 3. Rabbit-ear all 4. Fold all corners all flaps. Inflate the bottom to form a square base. Fold front and 2. Valley fold 3. Outside reverse 6. Outside reverse 7. Inside reverse 8. Fold all flaps 2. Sink the tips of 3. Fold all flaps up 4. Inflate the down. Queen: Start after step 12 of page 1. Fold and unfold the 3. Inside reverse fold 4.
Tuck the left corner of down. Valley fold tips up to 6. Inflate the bottom to form the crown. The tips form a square base. Squash fold 2. Narrow each 3. Inflate the each flap upward.
The completed chess set. From left to right, the pieces are the pawn, the bishop, the knight, the rook, the queen, and the king. Actually, the pawn shown in the photo is an older version that did not have the long flaps tucked inside the model. The premise behind this series of chess pieces was to design a chess set that a could be folded from the same sized squares, b were 3D, and c were easily distinguishable.
The first piece to be designed was the knight, followed by the pawn, the bishop, and the queen. The rook came almost as an afterthought. Coot By Perry Bailey Copyright 2. White side up 1. Fold a square in half on the diagonal one direction then fold in half on the diagonal the other way.
NOTE: When the model is finished there should be a flap sticking up inside of the model you can fold 3. Fold the model in half, and over to lock the body together. Grab the inner flap again and bring at least part of it back up again. Grab the inner flap and reverse 4. Fold the long edge up to the fold that puppy all the way to the top on each side. The finished Coot! Just taking a break here to say to mention how far the tail sticks out all depends on step 2.
Reverse fold up the neck, part of neck is inside the body, you know the neck is right when it touches at the underlying layers in the front. Pleat the beak in a little for that waterfowl look! Another outside reverse fold for the head. Begin with a square of between 15 and 20cm, Fold diagonally in half again, crease firmly, with the white side faced up.
Fold diagonally and unfold. Separate the two vertical edges on the Turn the model over Fold the lower diagonal edges to the centre, crease firmly, and unfold. Lift the bottom corner of the first layer upwards while reverse folding the diagonal sides along Turn model over the crease lines made in Step 6. Fold down the triangular piece in the middle, crease firmly, and unfold.
Separate the two diagonal edges on Grasp the paper at the circled Fold down the flap at the back. Open out from the centre Fold and unfold, and fold the first two layers creasing firmly. Unfold model completely. Recrease the indicated valley fold lines as mountain folds. This will make Step 20 easier. Now collapse the paper again Separate and draw the diagonal edge of the first Fold as shown, crease firmly, and layer of the flaps on each side towards the centre, unfold.
Petal fold, tucking the excess Fold the excess corners paper under the lowest corner inwards, in line with the of the triangular pieces above. Fold up the lower triangular Now turn flaps and rabbit's ear fold the the lower pieces Fold the tip of the triangle to Fold and unfold on the left, as in Now bring the four diagonal edges to the Step Fold the model horizontally in The four vertical pieces will form the legs.
Reverse fold on the right and left. The point on the left will form the head and neck. Reverse fold slightly below the tip, then reverse fold again at the base of the tail piece on the right. Mountain fold the both sides of the neck within itself, then valley fold both sides of the tail piece as illustrated. Reverse fold the tail again. Now for the head. The model is presented for personal use. For any other applications please contact me at klundber mnsinc.
Fold and unfold along the long side. Pinch the top flap at the half way point to find the Valley fold in half. Repeat behind forming an accordion pleat. Valley fold the raw edges to 4. Note that the squash fold 5. Mountain fold the edges under. The meet at the center line opening and will not line up exactly with the idea is to reduce the width of the squash folding the corners.
Repeat step three handle by about one third. These creases on the other side and turn upright. Tah Dah!!! Fill the basket with 7. Slip the tab of the folded change and give to your favorite 6. Because step 5 is a judgment fold one wait person. If the bill is old roll side of the handle will be larger than the other. Mountain fold the still folded edge around following the creases to lock in place. These folds will lie about on the line of falling out. Open up the basket and square off the bottom.
Note: Drawings are not drawn to scale. Follow the written directions in the first few steps closer than the diagrams.
0コメント